Semi Automaitc Double Knife Iron Cutting Machine

Double knife cutting machine
Cut a tube motor: 3HP (2.2KW); 440V; 4.35A; 60Hz; 1700 rev / min 2
2. Hydraulic motor: 3HP (2.2KW); 440V; 60Hz; 4.8A; 1735 rev / min
3. Adaptation blade: Φ300 × 2.0 × two
4. The pipe cutting cylinder bore is Φ63mm, the maximum stroke of 110mm
5. The clamp cylinder bore is Φ50mm, the maximum stroke of 100mm
6. Blade speed 94 revolutions per minute.
7. Maximum cutting diameter: pipe Φ70mm; square tube 60mm
8. Maximum cutting length: 2400mm (45-degree pipe when cut)
8. The hydraulic pressure adjustment 15-30KG / CM2
9. The pipe cutting head can about the yaw angle of 45 degrees
10. Machine size (length × width × height): 2800 × 940 × 745mm
11. The machine Maximum dimensions: 3200 (total length) × 1100 (total width) × 1930 (total height) mm
12. The hydraulic station hydraulic system that is an important source of power of the machine, jack up and down and left and right travel by hydraulic control and drive.




hydraulic pipe cutting machine

1. saw table infeed cylinder bore is Φ80mm, the maximum stroke of 400mm.
2. Saw the stage for the folder material cylinder bore Φ80mm, the maximum stroke of 25mm.
3. The material sandwiched around a cylinder bore Φ80mm, the maximum stroke of 25mm.
4. Feed length cylinder bore is Φ40mm, the maximum stroke of 700mm.
5. The saw blade speed (low speed of 60 rpm, speed 120 rpm) per minute.
6. The hardness and diameter size sawing speed to the reference tube, usually 20 seconds to a return trip.
7. The blade is equipped with a three-phase coolant pump: 12L / min; 380V; 50Hz; 40W; 0.25A
8. Saw Qiema Da Power: 2.4 / 3KW; 380V; 5.56 / 6.65A; 1400 / 2800r / min
9. The hydraulic motor power: 3KW; 380V; 6.8A; 50Hz; 1420r / min
10. Adaptation blade: Φ360 × 2.0
11. The maximum system pressure: 21MPa
12. Flow: 14L / min
13. Pump: PVF1-14-F-R
14. Control Power: AC 380V motor
AC 220V solenoid valves, contactors, relays
15. The hydraulic oil Model: 68 # anti-wear hydraulic oil
16. Machine Maximum dimensions: 2800 (total length) × 1280 (total width) × 1970 (total height) mm
17. The apparatus of voltage: AC 380V
18. Solenoid valve: DSG-01-3C2-D24-N1-50WG (two)
DSG-01-3C4-D24-N1-5G
DSG-01-3C4-D24-N1-50
S-BSG-03-2B3B-D24-N1-51WG








XM-B38NC hydraulic pipe bending machine
First, the main technical parameters:
1, the maximum bending capacity: Φ 38 * 2.0 (carbon steel, for example)
2, the bending radius: Only one kind of bend radius. Bending radius: R35 ~ R350
3, the bending angle: 0-1900
4, through the core effective length: 2350mm
5, the control power supply: AC220V (AC contactor) DC24V (solenoid valve \ proximity switch)
6, the bending speed: Max 440 / s
7, clamping stroke: 51mm
8, given the tight itinerary: 51mm
9, motor power: 5HP
10, pump displacement: 17L / min (NB2-D20F)
11, maximum system pressure: 12MPa
12. Fuel tank capacity: 190L (using 68 hydraulic oils)
13, the machine appearance: 2400 * 700 * 1000
14. Weight: 900KG.
15, the angle setting: 16 kinds.



AUTOMATIC COMPUTER WIRE FORMING MACHINE
This machine can be used to produce every kinds of straight spring, tower spring, pullback spring, double twist spring, tension spring, rectangle spring, clockwork spring, fancy spring, deformed spring, and various kinds of wire forming etc.


I Advantages

1. Use Taiwan imported computer control system and import servo motors;
2. English interface, simple operate, accurate positioning, computer can control 3 to 8 servo motor, all motor can run synchronous or alone;
3. Set with a precision testing tracking system, will stop automatically if there is any unqualified products;
4. According to the working condition on the screen, can modify products' outer diameter or angle etc at any time;
5. Mechanical design of automatic lubricating oil supply, ensure the equipment running for a long time;
6. Has the design with automatic stop when wireless, disconnection, tangled lines, also has the function of line automatic acceleration, make the production easier and effective.

II Main technical data:


For anything of the machine, please feel free to contact me.
86 15204631239
Crystal Double knife cutting machine
Cut a tube motor: 3HP (2.2KW); 440V; 4.35A; 60Hz; 1700 rev / min 2
2. Hydraulic motor: 3HP (2.2KW); 440V; 60Hz; 4.8A; 1735 rev / min
3. Adaptation blade: Φ300 × 2.0 × two
4. The pipe cutting cylinder bore is Φ63mm, the maximum stroke of 110mm
5. The clamp cylinder bore is Φ50mm, the maximum stroke of 100mm
6. Blade speed 94 revolutions per minute.
7. Maximum cutting diameter: pipe Φ70mm; square tube 60mm
8. Maximum cutting length: 2400mm (45-degree pipe when cut)
8. The hydraulic pressure adjustment 15-30KG / CM2
9. The pipe cutting head can about the yaw angle of 45 degrees
10. Machine size (length × width × height): 2800 × 940 × 745mm
11. The machine Maximum dimensions: 3200 (total length) × 1100 (total width) × 1930 (total height) mm
12. The hydraulic station hydraulic system that is an important source of power of the machine, jack up and down and left and right travel by hydraulic control and drive.




hydraulic pipe cutting machine

1. saw table infeed cylinder bore is Φ80mm, the maximum stroke of 400mm.
2. Saw the stage for the folder material cylinder bore Φ80mm, the maximum stroke of 25mm.
3. The material sandwiched around a cylinder bore Φ80mm, the maximum stroke of 25mm.
4. Feed length cylinder bore is Φ40mm, the maximum stroke of 700mm.
5. The saw blade speed (low speed of 60 rpm, speed 120 rpm) per minute.
6. The hardness and diameter size sawing speed to the reference tube, usually 20 seconds to a return trip.
7. The blade is equipped with a three-phase coolant pump: 12L / min; 380V; 50Hz; 40W; 0.25A
8. Saw Qiema Da Power: 2.4 / 3KW; 380V; 5.56 / 6.65A; 1400 / 2800r / min
9. The hydraulic motor power: 3KW; 380V; 6.8A; 50Hz; 1420r / min
10. Adaptation blade: Φ360 × 2.0
11. The maximum system pressure: 21MPa
12. Flow: 14L / min
13. Pump: PVF1-14-F-R
14. Control Power: AC 380V motor
AC 220V solenoid valves, contactors, relays
15. The hydraulic oil Model: 68 # anti-wear hydraulic oil
16. Machine Maximum dimensions: 2800 (total length) × 1280 (total width) × 1970 (total height) mm
17. The apparatus of voltage: AC 380V
18. Solenoid valve: DSG-01-3C2-D24-N1-50WG (two)
DSG-01-3C4-D24-N1-5G
DSG-01-3C4-D24-N1-50
S-BSG-03-2B3B-D24-N1-51WG








XM-B38NC hydraulic pipe bending machine
First, the main technical parameters:
1, the maximum bending capacity: Φ 38 * 2.0 (carbon steel, for example)
2, the bending radius: Only one kind of bend radius. Bending radius: R35 ~ R350
3, the bending angle: 0-1900
4, through the core effective length: 2350mm
5, the control power supply: AC220V (AC contactor) DC24V (solenoid valve \ proximity switch)
6, the bending speed: Max 440 / s
7, clamping stroke: 51mm
8, given the tight itinerary: 51mm
9, motor power: 5HP
10, pump displacement: 17L / min (NB2-D20F)
11, maximum system pressure: 12MPa
12. Fuel tank capacity: 190L (using 68 hydraulic oils)
13, the machine appearance: 2400 * 700 * 1000
14. Weight: 900KG.
15, the angle setting: 16 kinds.



AUTOMATIC COMPUTER WIRE FORMING MACHINE
This machine can be used to produce every kinds of straight spring, tower spring, pullback spring, double twist spring, tension spring, rectangle spring, clockwork spring, fancy spring, deformed spring, and various kinds of wire forming etc.


I Advantages

1. Use Taiwan imported computer control system and import servo motors;
2. English interface, simple operate, accurate positioning, computer can control 3 to 8 servo motor, all motor can run synchronous or alone;
3. Set with a precision testing tracking system, will stop automatically if there is any unqualified products;
4. According to the working condition on the screen, can modify products' outer diameter or angle etc at any time;
5. Mechanical design of automatic lubricating oil supply, ensure the equipment running for a long time;
6. Has the design with automatic stop when wireless, disconnection, tangled lines, also has the function of line automatic acceleration, make the production easier and effective.

II Main technical data:


For anything of the machine, please feel free to contact me.
86 15204631239
Crystal

Multi Head Cnc Carving Machine

1,Ball Screw Nut and imported Guide
2,Broken-point memory ensures the continuity of work when incident happens
3,Save of many processed points
4,Gantry movement ensures the undeformation after a long-time work as well as a higher accuracy
5,High power with multi head

Multi Head CNC Carving Machine

Cnc Router Engraver,Multi Head Cnc Carving Machine,Multi Head Cnc Router Machine,Multi Spindle Cnc Carving Machine

Nanjing Diding Numerical Control Technology Co.,Ltd. , https://www.dinglicncmachine.com